If your trolling motor’s pull rope has seen better days, it’s time to replace it. Luckily, this is a relatively easy process that anyone can do. All you’ll need is a new pull rope, a pair of pliers, and a screwdriver.
With these tools and a little bit of patience, you’ll have your trolling motor up and running in no time.
- Locate the pull rope end cap on the trolling motor
- Unscrew the end cap, and remove the old pull rope
- Cut a new piece of rope to the same length as the old rope, and thread it through the end cap
- Screw the end cap back on, and test the new pull rope
Replacing Your Trolling Motor Pull Cord Rope
How do you replace the pull cord on a Motorguide trolling motor?
If your Motorguide trolling motor is giving you trouble, it might be time to replace the pull cord. Luckily, this is a relatively easy fix that you can do yourself. Here’s a step-by-step guide on how to replace the pull cord on a Motorguide trolling motor.
1. Disconnect the power. Before you do anything, make sure to disconnect the power to the trolling motor. This is for your safety and to prevent any damage to the motor.
2. Remove the cover. Once the power is disconnected, you can remove the cover of the trolling motor. This will give you access to the pull cord.
3. Cut the old cord. Use a pair of scissors or a knife to cut the old cord. Make sure to cut it as close to the housing as possible.
4. Thread the new cord. Take the new cord and thread it through the housing. Make sure that you leave enough slack so that you can easily grip the cord when you need to.
5. Tie a knot. Once the cord is threaded through, tie a knot at the end. This will prevent the cord from slipping out.
6. Replace the cover. Put the cover back on the trolling motor and screw it into place.
7. Reconnect the power. Once everything is back in place, you can reconnect the power and test out the new cord.
How do you fix a trolling motor handle?
If you’re having trouble with your trolling motor handle, there are a few things you can do to try and fix it. First, make sure that the handle is securely fastened to the trolling motor. Sometimes, the handle can become loose over time and simply needs to be tightened.
If the handle is still loose after tightening, you may need to replace the handle.
Another thing you can try is to lubricate the handle. If the handle is sticking or hard to move, lubricating it may help.
Use a light oil or lubricant and apply it to the handle. Move the handle back and forth to work the lubricant into the mechanism.
If neither of these solutions works, the problem may be with the trolling motor itself.
In this case, you’ll need to take the trolling motor to a qualified technician to have it repaired or replaced.
Credit: www.louisianasportsman.com
Diy trolling motor pull cord
If your trolling motor pull cord has seen better days, or if you just want to save some money by doing it yourself, then this tutorial is for you! It’s actually pretty easy to replace your own trolling motor pull cord, and you’ll only need a few tools and supplies.
First, you’ll need to gather up a new pull cord, some wire cutters, and some electrical tape.
You’ll also need a screwdriver to remove the old cord.
Once you have everything you need, start by unscrewing the old cord from the trolling motor. Be careful not to lose any of the small parts!
Next, take your new cord and thread it through the trolling motor, just like the old one. Make sure to leave enough slack so that you can easily pull the cord when you’re out on the water.
Finally, use the wire cutters to trim any excess cord, and then use the electrical tape to secure the end of the cord.
That’s it! You’ve successfully replaced your trolling motor pull cord.
Trolling motor pull rope
If you’ve ever been out on a boat, you’ve probably seen a trolling motor in action. But what exactly is a trolling motor? And how does it work?
A trolling motor is a small, electrically-powered motor that is used to propel a boat forward at slow speeds. Trolling motors are typically used on smaller boats, such as fishing boats, where the added maneuverability can be helpful in getting to those hard-to-reach fishing spots.
So how does a trolling motor work?
It’s actually pretty simple. The trolling motor is mounted on the back of the boat, and a long rope is attached to it. The operator of the boat then uses the rope to pull the trolling motor back and forth, which propels the boat forward.
The trolling motor pull rope is an essential part of the trolling motor, and it’s important to choose the right one for your boat. There are a few things to consider when selecting a trolling motor pull rope, such as length, material, and breaking strength.
length: The length of the trolling motor pull rope will determine how much of the motor is in the water, and how much is above the waterline.
A longer rope will keep more of the motor out of the water, which can be helpful in shallow waters.
material: The material of the trolling motor pull rope is also important to consider. Nylon rope is a popular choice because it’s strong and durable.
Trolling motor rope knot
If you’re an avid fisherman, then you know that having a trolling motor is a necessity. But did you know that there’s a particular way to tie your trolling motor rope so that it doesn’t come undone? It’s called the trolling motor rope knot and it’s easy to learn.
Here’s how to do it:
1. Take the end of the rope and make a small loop.
2. Thread the end of the rope through the loop.
3. Pull the end of the rope tight.
4. Wrap the rope around the base of the trolling motor.
5. Thread the end of the rope through the loop again.
6. Pull the end of the rope tight.
Now you know how to tie the trolling motor rope knot. Be sure to practice it a few times so that you can do it quickly and easily when you’re out on the water.
Conclusion
If your Motorguide trolling motor is in need of a new pull rope, don’t worry – it’s a quick and easy fix! Just follow these simple steps and you’ll have your trolling motor up and running in no time.
1. Begin by removing the old pull rope from the trolling motor.
You can do this by simply pulling it through the sheath.
2. Cut a new piece of rope to the desired length, making sure it is long enough to comfortably reach the ground when the trolling motor is in the water.
3. Thread the new rope through the sheath, being careful not to damage the sheath in the process.
4. Tie a knot in the end of the rope, making sure it is secure.
5. Test the new pull rope by pulling on it to make sure it is securely attached to the trolling motor.
And that’s it!
You’ve now successfully replaced the pull rope on your Motorguide trolling motor.
0